9-Volt deluxe battery compartment, with access door, Black, hole size: 36,5x66,7mm (1-7/16 x 2-5/8 inch).

CTS 500k log sealed premium pot, special audio taper, 10% tolerance, split shaft.

CTS No-Load potentiometer with metal axis. Includes nut, lock and dress washer. Axis diameter: 6,0mm. Split knurled shaft. Thread bushing length: 9,5mm (3/8 inch). 500k log. Most commonly used in American amps and guitars. Smooth action - top quality!

Long Life CTS potentiometer with metal axis. Includes nut, lock and dress washer. Axis diameter: 6,0mm. Split knurled shaft. Thread bushing length: 9,5mm (3/8 inch). 250k log. 4 contacts to wafer for best reliability. Lifecycle rating: 250000 cycles. Smooth action - top quality!

CTS 17mm stereo balance/blend linear taper potentiometer with center detent. Knurled split shaft. Includes nut and washer.
These high quality audio potentiometers made by CTS are suitable for use in both professional and consumer applications. The most popular applications are electric guitars, sound processing equipment, and sound system amplifiers.

Humbucking bobbin, slug side, 53mm (2-3/32 inch) spacing. Cream.

Mini humbucking bobbin set (2 pcs.) black.

Pickup cover set for Mini Humbucker pickups, 1-15/16 inch string spacing. Set contains 2 pieces. Gold.

Nickel. Licensed by Duesenberg - Mounted in place of a stop tailpiece. No drilling, no routing, simply screw into the two existing threaded bushings with the enclosed bolts. With round lever for optimum handling! Incl. metric and US screws. Important: The distance between the tailpiece bolts must be exactly 81.5 mm (measured from centre to centre). Otherwise the Les Trem won't fit!

3 pole female XLR receptacle, grounding: without ground/shell contact, horizontal PCB mount

TONECVLT 50W, 12 inch, 12 Ohm, 50oz ceramic magnet, 1,75 inch voice coil. Bold and aggressive. Strong upper midrange punch. Good clarity, strong low end. Great for aggressive high-gain and down-tuned music, or to give your clean tone a bit of hair without losing definition.

CE manufactured FP type can caps are made in the USA to the same specifications. Twist lock / solder lugs.
Dimensions (D x L): 35x76 mm.

Marconi style Classic Concentric knob. Red with natural aluminum base. Diameter base: 25,5mm. Diameter knob: 17,8mm. Shadt diameter: 6/4mm. Set-screw.

Rectangular jack plate with recessed jack mounting hole. Metal, gold. Jack hole diameter: 9,5mm (3/8 inch ). Mounting screw holes spacing: 27,5 x 19,5mm (1-5/64 x 49/64 inch ). The jack plate has a slight curve to match the body's curved sides.

Control Plate for Tele Bass. Chrome finish.

Tokyo Cosmos aka TOCOS is known worldwide for their high quality potentiometers. The RV24 Series is a 24mm military-style carbon element potentiometer with a tolerance of 10%, praised by both guitar and hifi amp builders for their performance and reliability. Each potentiometer includes a nut, flush washer, and lock washer.

Aluminum blank panels for use with eurorack synths. These 1.6mm thick panels feature a painted black side and a bare aluminum side. Simply flip the panel around to match your color scheme. Elongated holes are used for the mounting holes to ensure a proper fit in your rack.

Oak Grigsby 2-Pole, 5-Way lever switch. This is a 1-wafer Super Switch, with stainless steel screws Fine quality, classic switch. Includes screws.

7189A TAD Selected

Weber SnufferStick High Voltage Discharge Stick. Clip to the chassis for ground, then hold on your filter caps to discharge dangerous high voltage present when you turn off your amp.

Guitar and Multi Tool Spanner Wrench for Tunematic Adjustment, Knobs, Jacks, Tuner Bushings.

Wood sanding block with contoured 12 inch radius.

Gorva DPDT toggle switch. On-On-On switching. PC Pins, medium length bat. Standard size (LxWxH): 12,7x11,43x8,89mm.

Illinois axial Capacitor 1500uF 25V. Tolerance: +/- 20%. Size (DxL): 0,512 x 1,024 inch (13,00mm x 26,00mm).

Mini-Reverb tank 8EB2C1B. These tanks are the perfect size for amps without a ton of space, pedal boards, studio equipment, and Eurorack and other synthesizers. They have been compacted into the smallest possible size that still provides a lush sounding spring reverb. 3 Springs, medium delay. Length: 17,8cm. 3 springs. 10 Ohm input impedance. 2575 Ohm output impedance.

Highly Insulated 9-pin Vacuum Tube Socket. Phosphorus bronze terminal pin with gold plating. Glassfiber filled PPS black body insulating material. Excellent clip contact for high-end audio. With panel saddle mounting.

D-shaft, mono Alpha potentiometer, with right angled PC mount vertical terminals. 9mm body diameter. Axis diameter: 6,3mm.

Fully insulated quick disconnect connectors for use with spade lugs. These connectors are size .187 inch and fit wire gauges 16-22AWG. These connectors are simple to attach to speaker wires using a crimping tool. Package of 10 pieces.

Jupiter Cosmos axial audio capacitor. Clarity and sparkle are the hallmarks of this great cap. Size (LxD): 17,5x8mm.

Fine Tune Bolt- Edge Zero

for Q54 / QX54QM / ICHI10

Ibanez Abs Tone Control Knob In White for Selected Signature / Rc / Rg / Gio Models
For Models: At10P,Grx140, Jem555,Jem70V, Rc330T,Rc365H,Rg440V,Rg550Xh

Ibanez Plate / Knop Set for Sst Preamp Lefthand

Instrument cable, 15ft, 1x angled, black

Adaptor, 3,5mm jack female mono, RCA male

Adaptor, RCA female, 6,3mm jack male mono

Blues harp, 20 reeds, ABS, A

Pickguard ‘50s Esquire, 5 screw holes, 1-ply, white

Mundorf Angelique is uniting the outstanding musical talents of Silver (structure, analytics, transparency) and Gold (multi-faceted tonality and brilliance) with the energy and liveliness of Copper in this one perfect alloy. Conductor Diameter: 1,0mm. Cross section: 0,7854mm². Specific Weight: 7,07 g/m. DC Resistance: 22 mOhm/Meter. Blue PTFE Insulation.

Deluxe Toggle Switch. 3-way. Nickel. Long-life model due to gold-plated contacts.

30MHz, High Output Current Operational Transconductance Amplifier (OTA). DIP8. Obsolete, available while supplies last.

Anodized aluminum knob with short indicator line and set screw. This slim, solid aluminum knob has a straight knurled grip with a diameter of 13mm. It also features a counterbore which allows it to hide pot bushings for a clean look. Fits 1/4 inch (6,35mm) pot shafts. Width: 13mm. Height: 15,8mm.

PC mount stereo jacks with a very low profile. These jacks have a smaller footprint than the Lumberg jacks that are popular for tight pedal builds. They are perfect for top mounted jack pedal builds and any other project where space is limited. Mounting nut and flat washer included.

High-quality USA made knobs from Rogan Corp. These solid phenolic knobs feature a brushed metal inlay in their unique diamond shaped grip. Often referred to as TV or cooker knobs, these genuine Rogans are used in a variety of Rickenbacker guitars and basses. Diameter: 38mm. Height: 16mm

This black color PCB is a recreation of the iss. 1 circuit board found in classic Fuzz Face pedals. When drawing the layout, multiple originals were closely referenced to ensure a proper match and fit. The copper traces are gold plated providing protection from corrosion indefinitely. This classic board fits the mounting holes on both original and reproduction Fuzz Face enclosures.

Pre-drilled three knob pedal enclosure made of pressed steel. This large enclosure is a close match to the original enclosures found on various vintage fuzz effects such as the Vox Tone Bender MKIII, Rotosound Fuzz, and Park Fuzz Sound. It features three holes for potentiometers, two top mounted holes for 3/8 inch jacks, and a footswitch hole. Comes with 4 rubber feet and a pack of mounting screws(packaged separately) for attaching the bottom plate.

The classic ABR-1 Replacement, Perfect for Les Pauls of the 50s and 60s, nickel. String spacing 52mm, bolt spacing 73,81mm, UNC 6-32 bolts, 12 inch radius, milled from aluminum.

Spare Bell Brass Tremolo block for ABM tremolo 5050-V.

The ideal mounting support for a 2504/Nashville bridge on M8. One pair of bolts 3,65mm on M8 (with built-in thumb-wheel). The perfect solution to adapt a 2504/Nashville bridge on the Asian M8 standard. Material: Bell Brass. Finish: Nickel.